00001
170MM
CHAIN RING
BOLT TORQUE
9Nm
Removal Instructions -
1. On the non-drive side unscrew the 2.5mm allen key bolt and turn the preload nut counterclockwise to remove all
preload from the crankset.
2. Unfasten drive-side fastening bolt with a 14mm allen wrench or 14mm Hex tool and remove driveside arm
3. Remove non-drive side arm and spindle from the bottom bracket.
Warranty Information
LIMITED TEN (10) YEAR WARRANTY ON CANE CREEK eeWings
Subject to the limitations, terms and conditions here of, Cane Creek warrants, to the original retail owner of each new Cane Creek eeWings, that the Cane
Creek eeWings, when new, is free from defects in materials and workmanship. This warranty expires ten (10) years from the date of the original Cane Creek
eeWings retail purchase from an authorized Cane Creek dealer or from a Cane Creek authorized original equipment manufacturer where Cane Creek
eeWings is included as original equipment on a purchased bike, unless otherwise dictated by requirement of law. NOTE: Stages power meters are not
covered under Cane Creek’s limited 10-year warranty. Refer to Stages terms of warranty.
TERMS OF WARRANTY
This warranty is conditioned on the Cane Creek eeWings being operated under normal conditions and properly maintained as specified by Cane Creek.
This warranty is only applicable to Cane Creek eeWings purchased new from an authorized Cane Creek source and is made only to the original retail
owner of the new Cane Creek eeWings and is not transferable to subsequent owners. This warranty is void if the Cane Creek eeWings is subjected to
abuse, neglect, improper or unauthorized repair, improper or unauthorized service or maintenance, alteration, modification, accident or other abnormal,
excessive, or improper use. Should it be determined, by Cane Creek in its sole and final discretion, that a Cane Creek eeWings is covered by this warranty,
it will be repaired or replaced, by a comparable model, at Cane Creek’s sole option, which will be conclusive and binding. THIS IS THE EXCLUSIVE REMEDY
UNDER THIS WARRANTY. ANY AND ALL OTHER REMEDIES AND DAMAGES THAT MAY OTHERWISE BE APPLICABLE ARE EXCLUDED, INCLUDING,
BUT NOT LIMITED TO, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR PUNITIVE DAMAGES. This limited warranty does not apply to normal wear
and tear, malfunctions or failures that result from abuse, improper assembly, neglect, alteration, improper maintenance, crash, misuse or collision. This
limited warranty gives the consumer specific legal rights. The consumer may also have other legal rights which vary from state to state or country to
country. Some states and countries do not allow the exclusion or limitation of incidental or consequential damages or warranties, so the above limitations
or exclusions may not apply to you. If it is determined by a court of competent jurisdiction that a certain provision of this limited warranty does not apply,
such determination shall not aect any other provision of this limited warranty and all other provisions shall remain in eect.
THIS IS THE ONLY WARRANTY MADE BY CANE CREEK ON ITS PRODUCTS AND COMPONENTS, AND THERE ARE NO WARRANTIES
THAT EXTEND BEYOND THE DESCRIPTION HEREIN. ANY WARRANTIES THAT MAY OTHERWISE BE IMPLIED BY LAW INCLUDING, BUT
NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED.
Step 3: Crankset Installation -
1. Apply Ti-Prep or grease to the spindle of the non-drive side arm and
inner bearing race of the bottom bracket.
2. Confirm all preload is removed from the preload nut. The preload nut
should be as close too the non-drive side crank arm as possible prior to
installation. See Figure C
3. Apply a thin layer of Ti-prep to the threads of the fastening bolt.
4. Install 1mm spacer onto the spindle and any other spacers required and
install drive side crank arm with chainring, making sure the crank arms
are correctly aligned. Confirm the fastening bolt washer is in the correct
orientation on the fastening bolt, refer to drawing D. Torque the 14mm
Allen key of the fastening bolt to 52Nm (38.35 ft-lb).
*It is imperative that this be done with a high quality, well-calibrated
torque wrench. It is not sucient to tighten the fixing bolt by hand!
5. Using the preload nut, remove any gap between the non-drive side
crank arm and the bearing cover by turning the preload nut clockwise
by hand. Once the gap is removed and the crank arms have no side to
side play, fasten the 2.5mm allen wrench bolt to 1.4Nm (12.4in-lb) on the
preload nut to secure the set preload.
6. Apply ti-prep to pedal threads and install pedals to pedal manufacturers
instructions for pedal torque. Pedal insert washers are not required.
AAI0044
spacer
Use 14mm Hex tool
Torque to 52Nm
1mm spindle
spacer
edge in
insert rounded
(38.35ft-lbs)
2.5mm Hex key
torque to 1.4Nm
(12.4in-lbs)
C
D
E
If this eeWings Crankset is equip with a Stages Power
Meter please refer to the Stages Instructions