00001
170MM
CHAIN RING
BOLT TORQUE
9Nm
Removal Instructions
1. On the non-drive side unscrew the 2.5mm allen key bolt and turn the preload nut counterclockwise to remove all preload
from the crankset.
2. Unfasten drive-side fastening bolt with a 14mm allen wrench or 14mm Hex tool and remove driveside arm
3. Remove non-drive side arm and spindle from the bottom bracket.
Warranty Information LIMITED TEN (10) YEAR WARRANTY ON CANE CREEK eeWings
Subject to the limitations, terms and conditions here of, Cane Creek warrants, to the original retail owner of each new Cane Creek eeWings, that the Cane
Creek eeWings, when new, is free from defects in materials and workmanship. This warranty expires ten (10) years from the date of the original
Cane Creek eeWings retail purchase from an authorized Cane Creek dealer or from a Cane Creek authorized original equipment manufacturer where
Cane Creek eeWings is included as original equipment on a purchased bike, unless otherwise dictated by requirement of law.
TERMS OF WARRANTY
This warranty is conditioned on the Cane Creek eeWings being operated under normal conditions and properly maintained as
specified by Cane Creek. This warranty is only applicable to Cane Creek eeWings purchased new from an authorized Cane Creek
source and is made only to the original retail owner of the new Cane Creek eeWings and is not transferable to subsequent owners.
This warranty is void if the Cane Creek eeWings is subjected to abuse, neglect, improper or unauthorized repair, improper or
unauthorized service or maintenance, alteration, modification, accident or other abnormal, excessive, or improper use. Should
it be determined, by Cane Creek in its sole and final discretion, that a Cane Creek eeWings is covered by this warranty, it will be
repaired or replaced, by a comparable model, at Cane Creek’s sole option, which will be conclusive and binding. THIS IS THE
EXCLUSIVE REMEDY UNDER THIS WARRANTY. ANY AND ALL OTHER REMEDIES AND DAMAGES THAT MAY OTHERWISE
BE APPLICABLE ARE EXCLUDED, INCLUDING, BUT NOT LIMITED TO, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR
PUNITIVE DAMAGES. This limited warranty does not apply to normal wear and tear, malfunctions or failures that result from
abuse, improper assembly, neglect, alteration, improper maintenance, crash, misuse or collision. This limited warranty gives
the consumer specific legal rights. The consumer may also have other legal rights which vary from state to state or country to
country. Some states and countries do not allow the exclusion or limitation of incidental or consequential damages or warranties,
so the above limitations or exclusions may not apply to you. If it is determined by a court of competent jurisdiction that a certain
provision of this limited warranty does not apply, such determination shall not affect any other provision of this limited warranty
and all other provisions shall remain in effect.
THIS IS THE ONLY WARRANTY MADE BY CANE CREEK ON ITS PRODUCTS AND COMPONENTS, AND THERE ARE
NO WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION HEREIN. ANY WARRANTIES THAT MAY OTHERWISE
BE IMPLIED BY LAW INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A
PARTICULAR PURPOSE ARE EXCLUDED.
Step 3: Crankset Installation -
1. Apply Ti-Prep or grease to the spindle of the non-drive side arm and inner
bearing race of the bottom bracket.
2. Confirm all preload is removed from the preload nut. The preload nut
should
be as close too the non-drive side crank arm as possible prior to installation.
See Figure C
3. Apply a thin layer of Ti-prep to the threads of the fastening bolt.
4. Install 1.75mm spacer onto the spindle and any other spacers required (refer
to bottom bracket chart in Step 1) and install drive side crank arm with
chainring, making sure the crank arms are correctly aligned. Confirm the
fastening bolt washer is in the correct orientation on the fastening bolt, refer
to drawing D. Torque the 14mm Allen key of the fastening bolt to 52Nm
(38.35 ft-lb).
5. Using the preload nut, remove any gap between the non-drive side crank arm
and the bearing cover by turning the preload nut clockwise by hand. Once
the gap is removed and the crank arms have no side to side play, fasten the
2.5mm allen wrench bolt to 1.4Nm (12.4in-lb) on the preload nut to secure the
set preload.
6. Install pedals into the pedal insert threads. Refer to pedal manufacturers
instructions for pedal torque. Pedal insert washers are not required.
Step 2: Install Chainring -
1. eeWings use the *
SRAM X-SYNC
®
direct mount chainring interface
2. Place a compatible chainring onto the crank arm.
3. Apply a thin layer of Ti-Prep (small brown tube included in packaging) to
the threads of each chain ring bolt. Then, Install T25 chain ring bolts onto
the crank arm and fasten bolts to 8-9Nm (71-80 in-lb)
*SRAM X-SYNC
®
is a registered trademark of SRAM, LLC
AAI0034
1.75mm spindle
spacer
Use 14mm Hex tool
Torque to 52Nm
1.75mm spindle
spacer
edge in
insert rounded
(38.35ft-lbs)
2.5mm Hex key
torque to 1.4Nm
(12.4in-lbs)
T25 Torx
8 - 9Nm
(5.9 - 6.6ft-lbs)
B
C
D
E
Rear Wheel Spacing
Chainring Offset
142mm
6mm
148mm 3mm
157mm 0mm